top of page
Scentroid Logo.jpg

Brands / Scentroid (USA)

Air Quality & Odour Monitoring System

SL-50 Scentinal

Air Quality and Odour Monitoring Station

Indoor Air Quality Monitor

AQSAFE IAQ Monitor

Indoor Air Quality Monitoring Station

Drone Based Air Quality Analyzer

Olfactometer Series

olfactometer.png
youtube.png
youtube.png
youtube.png

SM 100

The world’s most accurate in-field odour measuring device that allows users to accurately quantify ambient odour strength in OU/m3.

SM 100I

Takes out all guesswork from personal olfactometry by automatically selecting dilution steps and screening panelists for accuracy.

SC 300

Allows for a full odour lab to be deployed anywhere in a matter of minutes. Just plug it in and you're ready

to go!

SC 300P

Specialized multi-sensory olfactometer with EEG and FNIR capabilities for advance psychological and physiological research.

olfactometer-1.png

SS 400

The world’s only portable six (6) panel olfactometer. It's small size will allow for a perfect on table setup with 6 panelists.

SS 600

The 6 station olfactometry lab is amazingly advanced and fully automated, being capable of odour measurement and analysis.

N-BUTANOL-KIT

Need to train a new odour panelist? Conducting the N-Butanol test is your next step!

Sampler Series

Untitled.png

HEATED PURGER

Designed to provide an effective and reliable cleaning solutions for olfactometers, sample bags, PTFE lines, and other equipment.

OXIDISATION PURGER

Designed to provide an effective and reliable cleaning solution for olfactometers, sample bags, PTFE lines, and other equipment.

STACK DILUTING

Provides accurate pre-dilution of high temperature gas emissions with nitrogen or zero-air to minimize condensation.

VACUUM CHAMBER

Easy to use, portable, and serves as a cost-effective air sampling collection device.

Untitled-1.png

FLUX CHAMBER 

The Scentroid Flux chamber (AKA Emission Isolation Flux Hood) is used to determine levels of emissions from solid or liquid surfaces.

WIND TUNNEL 

The Scentroid SW60 is the next generation Wind Tunnel Sampler used for sampling on solid or liquid surfaces with passive odour emissions.

STATIC HOOD

Provides an easy to use and contaminate-free solution for taking air samples.

Sampling Bags & Fittings

sampling bags

Nalophan Bags 

Nalophan is an inexpensive material used for making disposable sampling bags. Nalophan  can be purchased pre-made or as a large roll to reduce cost. Nalophan provides a cost effective solution but has the shortest holding time for most compounds such as H2S, Ammonia and VOCs.

Tedlar Bags

Tedlar is the standard in air sampling for 20 years now. Tedlar bags will provide a reusable storage medium with good retention for most substances. Scentroid Tedlar bags are made of 2mm thick film and purged at 100 °C using Scentroid’s patented heat/vacuum SP20 Purger. Sampling bags are pressure tested and leak tested to ensure the utmost perfect quality.

PTFE Bags

Scentroid Is the only manufacturer offering PTFE sampling bags. These bags offer a much higher resistance to contamination and Scentroid’s PTFE Sampling Bags have a longer holding time than Tedlar bags. They are also the only accepted bag material for all standards. PTFE Sampling bags are extremely resistant to contamination and therefore can be easily cleaned and reused. They have been approved by the Ministry of the Environment in Ontario and almost every other jurisdiction around the world.

Stainless Steel Bags

Scentroid is the only manufacturer in the world to offer stainless steel sampling bags. Each stainless steel bag is made of electro-polished marine grade (316L series) stainless steel film. Stainless steel sampling bags are ideal for sampling corrosive materials such as high H2S or benzene. Stainless steel is rolled into a thin film that provides it with flexibility while maintaining the 100% sample preservation. Scentroid stainless Steel bags are used more often than Sumo canisters.

fittings.png

2 in 1 Polypropylene

On/Off valve function with replaceable septum in a single unit. Quick, easy opening and closing of valve. Less than one half turn opens/closes the valve. These fittings fit 4/1” & 6 mm tubing

2 IN 1 PTFE FITTING

The combination fitting and septum is made of pure PTFE and offers high corrosion resistance. The fittings are light weight and therefore provide an excellent choice for PTFE sample bags

PTFE COATED NYLON

These fitting offer zero resistance with sample flow and therefore are the ideal choice for large sample bags. They also allow attaching tubing or syringe sample extraction by changing caps

STAINLESS STEEL FITTING

These all stainless steel fittings are used only on Scentroid stainless bags. This type of fitting is highly resistant to corrosive materials and can be used in high temperature sampling

bottom of page